Information gathering

Ninguna herramienta coincide.

• 0traceweb

  Runs a traceroute inside an already-open TCP connection so intermediate hops show up when ICMP is filtered.

• arpingweb

  Sends ARP requests on the local link to see which MAC claims an IP when ICMP is filtered.

  ayuda

  ARPing 2.29, by Thomas Habets <thomas@habets.se>
  usage: arping [ -0aAbdDeFpPqrRuUvzZ ] [ -w <sec> ] [ -W <sec> ] [ -S <host/ip> ]
                [ -T <host/ip ] [ -s <MAC> ] [ -t <MAC> ] [ -c <count> ]
                [ -C <count> ] [ -i <interface> ] [ -m <type> ] [ -g <group> ]
                [ -V <vlan> ] [ -Q <priority> ] <host/ip/MAC | -B>
  
  Options:
  
      -0     Use this option to ping with source IP address 0.0.0.0. Use this
             when you haven't configured your interface yet.  Note that  this
             may  get  the  MAC-ping  unanswered.   This  is  an alias for -S
             0.0.0.0.
      -a     Audiable ping.
      -A     Only count addresses matching  requested  address  (This  *WILL*
             break  most things you do. Only useful if you are arpinging many
             hosts at once. See arping-scan-net.sh for an example).
      -b     Like -0 but source broadcast source  address  (255.255.255.255).
             Note that this may get the arping unanswered since it's not nor-
             mal behavior for a host.
      -B     Use instead of host if you want to address 255.255.255.255.
      -c count
             Only send count requests.
      -C count
             Only wait for this many replies, regardless of -c and -w.
      -d     Find duplicate replies. Exit with 1 if there are answers from
             two different MAC addresses.
      -D     Display answers as exclamation points and missing packets as dots.
      -e     Like -a but beep when there is no reply.
      -F     Don't try to be smart about the interface name.  (even  if  this
             switch is not given, -i overrides smartness)
      -g group
             setgid() to this group instead of the nobody group.
      -h     Displays a help message and exits.
      -i interface
             Use the specified interface.
      -m type
             Type of timestamp to use for incoming packets. Use -vv when
             pinging to list available ones.
      -q     Does not display messages, except error messages.
      -Q pri 802.1p priority to set. Should be used with 802.1Q (-V).
             Defaults to 0.
      -r     Raw output: only the MAC/IP address is displayed for each reply.
      -R     Raw output: Like -r but shows "the other one", can  be  combined
             with -r.
      -s MAC Set source MAC address. You may need to use -p with this.
  … (28 more lines — see the tool's home page)

• braaweb

  Mass SNMP walker for querying many agents quickly once communities are known and authorized.

• dmitryweb

  Deepmagic info-gathering for whois, emails, subdomains, and port hints from a single host or domain name.

  ayuda

  dmitry: invalid option -- 'h'
  Deepmagic Information Gathering Tool
  "There be some deep magic going on"
  
  Usage: dmitry [-winsepfb] [-t 0-9] [-o %host.txt] host
    -o	 Save output to %host.txt or to file specified by -o file
    -i	 Perform a whois lookup on the IP address of a host
    -w	 Perform a whois lookup on the domain name of a host
    -n	 Retrieve Netcraft.com information on a host
    -s	 Perform a search for possible subdomains
    -e	 Perform a search for possible email addresses
    -p	 Perform a TCP port scan on a host
  * -f	 Perform a TCP port scan on a host showing output reporting filtered ports
  * -b	 Read in the banner received from the scanned port
  * -t 0-9 Set the TTL in seconds when scanning a TCP port ( Default 2 )
  *Requires the -p flagged to be passed

• dnsenumweb

  Walks DNS for a domain: records, transfers when allowed, and name guesses that expand your map before you touch an app.

  ayuda

  dnsenum VERSION:1.3.1
  Usage: dnsenum [Options] <domain>
  [Options]:
  Note: If no -f tag supplied will default to /usr/share/dnsenum/dns.txt or
  the dns.txt file in the same directory as dnsenum
  GENERAL OPTIONS:
    --dnsserver 	<server>
  			Use this DNS server for A, NS and MX queries.
    --enum		Shortcut option equivalent to --threads 5 -s 15 -w.
    -h, --help		Print this help message.
    --noreverse		Skip the reverse lookup operations.
    --nocolor		Disable ANSIColor output.
    --private		Show and save private ips at the end of the file domain_ips.txt.
    --subfile <file>	Write all valid subdomains to this file.
    -t, --timeout <value>	The tcp and udp timeout values in seconds (default: 10s).
    --threads <value>	The number of threads that will perform different queries.
    -v, --verbose		Be verbose: show all the progress and all the error messages.
  GOOGLE SCRAPING OPTIONS:
    -p, --pages <value>	The number of google search pages to process when scraping names,
  			the default is 5 pages, the -s switch must be specified.
    -s, --scrap <value>	The maximum number of subdomains that will be scraped from Google (default 15).
  BRUTE FORCE OPTIONS:
    -f, --file <file>	Read subdomains from this file to perform brute force. (Takes priority over default dns.txt)
    -u, --update	<a|g|r|z>
  			Update the file specified with the -f switch with valid subdomains.
  	a (all)		Update using all results.
  	g		Update using only google scraping results.
  	r		Update using only reverse lookup results.
  	z		Update using only zonetransfer results.
    -r, --recursion	Recursion on subdomains, brute force all discovered subdomains that have an NS record.
  WHOIS NETRANGE OPTIONS:
    -d, --delay <value>	The maximum value of seconds to wait between whois queries, the value is defined randomly, default: 3s.
    -w, --whois		Perform the whois queries on c class network ranges.
  			 **Warning**: this can generate very large netranges and it will take lot of time to perform reverse lookups.
  REVERSE LOOKUP OPTIONS:
    -e, --exclude	<regexp>
  			Exclude PTR records that match the regexp expression from reverse lookup results, useful on invalid hostnames.
  OUTPUT OPTIONS:
    -o --output <file>	Output in XML format. Can be imported in MagicTree (www.gremwell.com)

• dnsmapweb

  Brute-forces DNS names under a domain from a wordlist so hidden hosts show up beside the ones in public records.

  ayuda

  dnsmap 0.36 - DNS Network Mapper
  
  [+] error: entered domain is not valid!

• dnsreconweb

  DNS enumeration helper for records, zone transfer attempts, and common name patterns.

  ayuda

  usage: dnsrecon [-h] [-d DOMAIN] [-iL INPUT_LIST] [-n NS_SERVER] [-r RANGE]
                  [-D DICTIONARY] [-f] [-a] [-s] [-b] [-y] [-k] [-w] [--shodan]
                  [--shodan-active] [--shodan-key SHODAN_KEY] [-z]
                  [--threads THREADS] [--lifetime LIFETIME]
                  [--loglevel {DEBUG,INFO,WARNING,ERROR,CRITICAL}] [--tcp]
                  [--db DB] [-x XML] [-c CSV] [-j JSON] [--iw]
                  [--disable_check_nxdomain] [--disable_check_recursion]
                  [--disable_recurs] [--disable_check_bindversion] [-V] [-v]
                  [-t TYPE]
  
  options:
    -h, --help            show this help message and exit
    -d, --domain DOMAIN   Target domain.
    -iL, --input-list INPUT_LIST
                          File containing a list of domains to perform DNS enumeration on, one per line.
    -n, --name_server NS_SERVER
                          Domain server to use. If none is given, the SOA of the target will be used. Multiple servers can be specified using a comma separated list.
    -r, --range RANGE     IP range for reverse lookup brute force in formats (first-last) or in (range/bitmask).
    -D, --dictionary DICTIONARY
                          Dictionary file of subdomain and hostnames to use for brute force.
    -f                    Filter out of brute force domain lookup, records that resolve to the wildcard defined IP address when saving records.
    -a                    Perform AXFR with standard enumeration.
    -s                    Perform a reverse lookup of IPv4 ranges in the SPF record with standard enumeration.
    -b                    Perform Bing enumeration with standard enumeration.
    -y                    Perform Yandex enumeration with standard enumeration.
    -k                    Perform crt.sh enumeration with standard enumeration.
    -w                    Perform deep whois record analysis and reverse lookup of IP ranges found through Whois when doing a standard enumeration.
    --shodan              Use Shodan to query netblocks discovered via SPF (-s) and/or Whois (-w) during standard enumeration.
    --shodan-active       Actively validate Shodan-discovered names by resolving them and confirming they still match the queried netblock.
    --shodan-key SHODAN_KEY
                          Shodan API key. If omitted, SHODAN_API_KEY environment variable is used.
    -z                    Performs a DNSSEC zone walk with standard enumeration.
    --threads THREADS     Number of threads to use in reverse lookups, forward lookups, brute force and SRV record enumeration.
    --lifetime LIFETIME   Time to wait for a server to respond to a query. default is 3.0
    --loglevel {DEBUG,INFO,WARNING,ERROR,CRITICAL}
                          Log level to use. default is INFO
    --tcp                 Use TCP protocol to make queries.
    --db DB               SQLite 3 file to save found records.
    -x, --xml XML         XML file to save found records.
    -c, --csv CSV         Save output to a comma separated value file.
    -j, --json JSON       save output to a JSON file.
    --iw                  Continue brute forcing a domain even if a wildcard record is discovered.
    --disable_check_nxdomain
                          Disables check for NXDOMAIN hijacking on name servers.
    --disable_check_recursion
  … (22 more lines — see the tool's home page)

• dnstracerweb

  Follows DNS delegation from the root toward an answer so broken chains become visible.

• dnswalkweb

  Checks zone data via nameserver queries for inconsistencies during DNS review.

• enum4linuxweb

  Talks SMB/NetBIOS to list shares, users, and groups on Windows and Samba hosts during early recon.

  ayuda

  ./enum4linux.pl version [unknown] calling Getopt::Std::getopts (version 1.14 [paranoid]),
  running under Perl version 5.42.2.
  
  Usage: enum4linux.pl [-OPTIONS [-MORE_OPTIONS]] [--] [PROGRAM_ARG1 ...]
  
  The following single-character options are accepted:
  	With arguments: -u -p -f -R -s -k -w -K
  	Boolean (without arguments): -U -M -N -S -P -G -l -L -D -d -r -v -A -o -h -n -a -i -P
  
  Options may be merged together.  -- stops processing of options.
  Space is not required between options and their arguments.
    [Now continuing due to backward compatibility and excessive paranoia.
     See 'perldoc Getopt::Std' about $Getopt::Std::STANDARD_HELP_VERSION.]
  enum4linux v0.9.1 (http://labs.portcullis.co.uk/application/enum4linux/)
  Copyright (C) 2011 Mark Lowe (mrl@portcullis-security.com)
  
  Simple wrapper around the tools in the samba package to provide similar
  functionality to enum.exe (formerly from www.bindview.com).  Some additional
  features such as RID cycling have also been added for convenience.
  
  Usage: ./enum4linux.pl [options] ip
  
  Options are (like "enum"):
      -U        get userlist
      -M        get machine list*
      -S        get sharelist
      -P        get password policy information
      -G        get group and member list
      -d        be detailed, applies to -U and -S
      -u user   specify username to use (default "")
      -p pass   specify password to use (default "")
  
  The following options from enum.exe aren't implemented: -L, -N, -D, -f
  
  Additional options:
      -a        Do all simple enumeration (-U -S -G -P -r -o -n -i).
                This option is enabled if you don't provide any other options.
      -h        Display this help message and exit
      -r        enumerate users via RID cycling
      -R range  RID ranges to enumerate (default: 500-550,1000-1050, implies -r)
      -K n      Keep searching RIDs until n consective RIDs don't correspond to
                a username.  Impies RID range ends at 999999. Useful
  	      against DCs.
      -l        Get some (limited) info via LDAP 389/TCP (for DCs only)
      -s file   brute force guessing for share names
  … (20 more lines — see the tool's home page)

• fierceweb

  Looks for non-contiguous IP space tied to a domain by DNS brute force and adjacent network guesses.

  ayuda

  usage: fierce [-h] [--domain DOMAIN] [--connect] [--wide]
                [--traverse TRAVERSE] [--search SEARCH [SEARCH ...]]
                [--range RANGE] [--delay DELAY]
                [--subdomains SUBDOMAINS [SUBDOMAINS ...] |
                --subdomain-file SUBDOMAIN_FILE]
                [--dns-servers DNS_SERVERS [DNS_SERVERS ...] |
                --dns-file DNS_FILE] [--tcp]
  
          A DNS reconnaissance tool for locating non-contiguous IP space.
  
  options:
    -h, --help            show this help message and exit
    --domain DOMAIN       domain name to test
    --connect             attempt HTTP connection to non-RFC 1918 hosts
    --wide                scan entire class c of discovered records
    --traverse TRAVERSE   scan NUMBER IPs before and after discovered records. This respects Class C boundaries and won't enter adjacent subnets.
    --search SEARCH [SEARCH ...]
                          filter on these domains when expanding lookup
    --range RANGE         scan an internal IP range, use cidr notation
    --delay DELAY         time to wait between lookups
    --subdomains SUBDOMAINS [SUBDOMAINS ...]
                          use these subdomains
    --subdomain-file SUBDOMAIN_FILE
                          use subdomains specified in this file (one per line)
    --dns-servers DNS_SERVERS [DNS_SERVERS ...]
                          use these dns servers for reverse lookups
    --dns-file DNS_FILE   use dns servers specified in this file for reverse lookups (one per line)
    --tcp                 use TCP instead of UDP

• firewalkweb

  Uses crafted packets to infer ACL rules on intermediate hops during authorized network mapping.

• fpingweb

  Pings many hosts in parallel to learn which addresses answer before deeper scans.

  ayuda

  Usage: fping [options] [targets...]
  
  Probing options:
     -4, --ipv4         only ping IPv4 addresses
     -6, --ipv6         only ping IPv6 addresses
     -b, --size=BYTES   amount of ping data to send, in bytes (default: 56)
     -B, --backoff=N    set exponential backoff factor to N (default: 1.5)
     -c, --count=N      count mode: send N pings to each target
     -f, --file=FILE    read list of targets from a file ( - means stdin)
     -g, --generate     generate target list (only if no -f specified)
                        (give start and end IP in the target list, or a CIDR address)
                        (ex. fping -g 192.168.1.0 192.168.1.255 or fping -g 192.168.1.0/24)
     -H, --ttl=N        set the IP TTL value (Time To Live hops)
     -I, --iface=IFACE  bind to a particular interface
     -l, --loop         loop mode: send pings forever
     -m, --all          use all IPs of provided hostnames (e.g. IPv4 and IPv6), use with -A
     -M, --dontfrag     set the Don't Fragment flag
     -O, --tos=N        set the type of service (tos) flag on the ICMP packets
     -p, --period=MSEC  interval between ping packets to one target (in ms)
                        (in loop and count modes, default: 1000 ms)
     -r, --retry=N      number of retries (default: 3)
     -R, --random       random packet data (to foil link data compression)
     -S, --src=IP       set source address
     -t, --timeout=MSEC individual target initial timeout (default: 500 ms,
                        except with -l/-c/-C, where it's the -p period up to 2000 ms)
  
  Output options:
     -a, --alive        show targets that are alive
     -A, --addr         show targets by address
     -C, --vcount=N     same as -c, report results in verbose format
     -d, --rdns         show targets by name (force reverse-DNS lookup)
     -D, --timestamp    print timestamp before each output line
     -e, --elapsed      show elapsed time on return packets
     -i, --interval=MSEC  interval between sending ping packets (default: 10 ms)
     -n, --name         show targets by name (reverse-DNS lookup for target IPs)
     -N, --netdata      output compatible for netdata (-l -Q are required)
     -o, --outage       show the accumulated outage time (lost packets * packet interval)
     -q, --quiet        quiet (don't show per-target/per-ping results)
     -Q, --squiet=SECS  same as -q, but add interval summary every SECS seconds
     -s, --stats        print final stats
     -u, --unreach      show targets that are unreachable
     -v, --version      show version
     -x, --reachable=N  shows if >=N hosts are reachable or not

• fragrouterweb

  Fragmenting IDS evasion router for lab tests against detection gear you own.

• hping3web

  Crafts custom ICMP/TCP/UDP packets for firewall mapping and path tests in a scoped lab.

  ayuda

  usage: hping3 host [options]
    -h  --help      show this help
    -v  --version   show version
    -c  --count     packet count
    -i  --interval  wait (uX for X microseconds, for example -i u1000)
        --fast      alias for -i u10000 (10 packets for second)
        --faster    alias for -i u1000 (100 packets for second)
        --flood	   sent packets as fast as possible. Don't show replies.
    -n  --numeric   numeric output
    -q  --quiet     quiet
    -I  --interface interface name (otherwise default routing interface)
    -V  --verbose   verbose mode
    -D  --debug     debugging info
    -z  --bind      bind ctrl+z to ttl           (default to dst port)
    -Z  --unbind    unbind ctrl+z
        --beep      beep for every matching packet received
  Mode
    default mode     TCP
    -0  --rawip      RAW IP mode
    -1  --icmp       ICMP mode
    -2  --udp        UDP mode
    -8  --scan       SCAN mode.
                     Example: hping --scan 1-30,70-90 -S www.target.host
    -9  --listen     listen mode
  IP
    -a  --spoof      spoof source address
    --rand-dest      random destionation address mode. see the man.
    --rand-source    random source address mode. see the man.
    -t  --ttl        ttl (default 64)
    -N  --id         id (default random)
    -W  --winid      use win* id byte ordering
    -r  --rel        relativize id field          (to estimate host traffic)
    -f  --frag       split packets in more frag.  (may pass weak acl)
    -x  --morefrag   set more fragments flag
    -y  --dontfrag   set don't fragment flag
    -g  --fragoff    set the fragment offset
    -m  --mtu        set virtual mtu, implies --frag if packet size > mtu
    -o  --tos        type of service (default 0x00), try --tos help
    -G  --rroute     includes RECORD_ROUTE option and display the route buffer
    --lsrr           loose source routing and record route
    --ssrr           strict source routing and record route
    -H  --ipproto    set the IP protocol field, only in RAW IP mode
  ICMP
    -C  --icmptype   icmp type (default echo request)
    -K  --icmpcode   icmp code (default 0)
  … (42 more lines — see the tool's home page)

• ike-scanweb

  Discovers and fingerprints IKE VPN gateways so you can see which IPsec proposals they offer.

  ayuda

  Usage: ike-scan [options] [hosts...]
  
  Target hosts must be specified on the command line unless the --file option is
  given, in which case the targets are read from the specified file instead.
  
  The target hosts can be specified as IP addresses or hostnames. You can also
  specify the target as IPnetwork/bits (e.g. 192.168.1.0/24) to specify all hosts
  in the given network (network and broadcast addresses included), or
  IPstart-IPend (e.g. 192.168.1.3-192.168.1.27) to specify all hosts in the
  inclusive range, or IPnetwork:NetMask (e.g. 192.168.1.0:255.255.255.0) to
  specify all hosts in the given network and mask.
  
  These different options for specifying target hosts may be used both on the
  command line, and also in the file specified with the --file option.
  
  In the options below a letter or word in angle brackets like <f> denotes a
  value or string that should be supplied. The corresponding text should
  indicate the meaning of this value or string. When supplying the value or
  string, do not include the angle brackets. Text in square brackets like [<f>]
  mean that the enclosed text is optional. This is used for options which take
  an optional argument.
  
  Options:
  
  --help or -h		Display this usage message and exit.
  
  --file=<fn> or -f <fn>	Read hostnames or addresses from the specified file
  			instead of from the command line. One name or IP
  			address per line.  Use "-" for standard input.
  
  --sport=<p> or -s <p>	Set UDP source port to <p>, default=500, 0=random.
  			Some IKE implementations require the client to use
  			UDP source port 500 and will not talk to other ports.
  			Note that superuser privileges are normally required
  			to use non-zero source ports below 1024.  Also only
  			one process on a system may bind to a given source port
  			at any one time. Use of the --nat-t option changes
  			the default source port to 4500
  
  --dport=<p> or -d <p>	Set UDP destination port to <p>, default=500.
  			UDP port 500 is the assigned port number for ISAKMP
  			and this is the port used by most if not all IKE
  			implementations. Use of the --nat-t option changes
  			the default destination port to 4500
  
  … (115 more lines — see the tool's home page)

• intraceweb

  Traceroute that rides an existing TCP connection when ICMP is filtered on the path.

• iputils-arpingweb

  Sends ARP-based reachability probes on the local link when ICMP echo is the wrong question.

• irpasweb

  Suite for abusing routing protocol behaviors in labs where you own the routers under test.

• masscanweb

  Very fast Internet-scale TCP port scanner; useful for wide lab ranges when you need coverage first.

  ayuda

  MASSCAN is a fast port scanner. The primary input parameters are the
  IP addresses/ranges you want to scan, and the port numbers. An example
  is the following, which scans the 10.x.x.x network for web servers:
   masscan 10.0.0.0/8 -p80
  The program auto-detects network interface/adapter settings. If this
  fails, you'll have to set these manually. The following is an
  example of all the parameters that are needed:
   --adapter-ip 192.168.10.123
   --adapter-mac 00-11-22-33-44-55
   --router-mac 66-55-44-33-22-11
  Parameters can be set either via the command-line or config-file. The
  names are the same for both. Thus, the above adapter settings would
  appear as follows in a configuration file:
   adapter-ip = 192.168.10.123
   adapter-mac = 00-11-22-33-44-55
   router-mac = 66-55-44-33-22-11
  All single-dash parameters have a spelled out double-dash equivalent,
  so '-p80' is the same as '--ports 80' (or 'ports = 80' in config file).
  To use the config file, type:
   masscan -c <filename>
  To generate a config-file from the current settings, use the --echo
  option. This stops the program from actually running, and just echoes
  the current configuration instead. This is a useful way to generate
  your first config file, or see a list of parameters you didn't know
  about. I suggest you try it now:
   masscan -p1234 --echo

• nbtscanweb

  Scans for NetBIOS names on a network segment to learn Windows host names without a full directory yet.

  ayuda

  "Human-readable service names" (-h) option cannot be used without verbose (-v) option.
  Usage:
  nbtscan [-v] [-d] [-e] [-l] [-t timeout] [-b bandwidth] [-r] [-q] [-s separator] [-m retransmits] (-f filename)|(<scan_range>)
  	-v		verbose output. Print all names received
  			from each host
  	-d		dump packets. Print whole packet contents.
  	-e		Format output in /etc/hosts format.
  	-l		Format output in lmhosts format.
  			Cannot be used with -v, -s or -h options.
  	-t timeout	wait timeout milliseconds for response.
  			Default 1000.
  	-b bandwidth	Output throttling. Slow down output
  			so that it uses no more that bandwidth bps.
  			Useful on slow links, so that ougoing queries
  			don't get dropped.
  	-r		use local port 137 for scans. Win95 boxes
  			respond to this only.
  			You need to be root to use this option on Unix.
  	-q		Suppress banners and error messages,
  	-s separator	Script-friendly output. Don't print
  			column and record headers, separate fields with separator.
  	-h		Print human-readable names for services.
  			Can only be used with -v option.
  	-m retransmits	Number of retransmits. Default 0.
  	-f filename	Take IP addresses to scan from file filename.
  			-f - makes nbtscan take IP addresses from stdin.
  	<scan_range>	what to scan. Can either be single IP
  			like 192.168.1.1 or
  			range of addresses in one of two forms:
  			xxx.xxx.xxx.xxx/xx or xxx.xxx.xxx.xxx-xxx.
  Examples:
  	nbtscan -r 192.168.1.0/24
  		Scans the whole C-class network.
  	nbtscan 192.168.1.25-137
  		Scans a range from 192.168.1.25 to 192.168.1.137
  	nbtscan -v -s : 192.168.1.0/24
  		Scans C-class network. Prints results in script-friendly
  		format using colon as field separator.
  		Produces output like that:
  		192.168.0.1:NT_SERVER:00U
  		192.168.0.1:MY_DOMAIN:00G
  		192.168.0.1:ADMINISTRATOR:03U
  		192.168.0.2:OTHER_BOX:00U
  		...
  	nbtscan -f iplist
  … (1 more lines — see the tool's home page)

• ncatweb

  Nmap's netcat reimplementation for listeners, connects, SSL, and simple data transfer.

  ayuda

  Ncat 7.99 ( https://nmap.org/ncat )
  Usage: ncat [options] [hostname] [port]
  
  Options taking a time assume seconds. Append 'ms' for milliseconds,
  's' for seconds, 'm' for minutes, or 'h' for hours (e.g. 500ms).
    -4                         Use IPv4 only
    -6                         Use IPv6 only
    -U, --unixsock             Use Unix domain sockets only
        --vsock                Use vsock sockets only
    -C, --crlf                 Use CRLF for EOL sequence
    -c, --sh-exec <command>    Executes the given command via /bin/sh
    -e, --exec <command>       Executes the given command
        --lua-exec <filename>  Executes the given Lua script
    -g hop1[,hop2,...]         Loose source routing hop points (8 max)
    -G <n>                     Loose source routing hop pointer (4, 8, 12, ...)
    -m, --max-conns <n>        Maximum <n> simultaneous connections
    -h, --help                 Display this help screen
    -d, --delay <time>         Wait between read/writes
    -o, --output <filename>    Dump session data to a file
    -x, --hex-dump <filename>  Dump session data as hex to a file
    -i, --idle-timeout <time>  Idle read/write timeout
    -p, --source-port port     Specify source port to use
    -s, --source addr          Specify source address to use (doesn't affect -l)
    -l, --listen               Bind and listen for incoming connections
    -k, --keep-open            Accept multiple connections in listen mode
    -n, --nodns                Do not resolve hostnames via DNS
    -t, --telnet               Answer Telnet negotiations
    -u, --udp                  Use UDP instead of default TCP
        --sctp                 Use SCTP instead of default TCP
    -v, --verbose              Set verbosity level (can be used several times)
    -w, --wait <time>          Connect timeout
    -z                         Zero-I/O mode, report connection status only
        --append-output        Append rather than clobber specified output files
        --send-only            Only send data, ignoring received; quit on EOF
        --recv-only            Only receive data, never send anything
        --no-shutdown          Continue half-duplex when receiving EOF on stdin
    -q <time>                  After EOF on stdin, wait <time> then quit.
        --allow                Allow only given hosts to connect to Ncat
        --allowfile            A file of hosts allowed to connect to Ncat
        --deny                 Deny given hosts from connecting to Ncat
        --denyfile             A file of hosts denied from connecting to Ncat
        --broker               Enable Ncat's connection brokering mode
        --chat                 Start a simple Ncat chat server
        --proxy <addr[:port]>  Specify address of host to proxy through
        --proxy-type <type>    Specify proxy type ("http", "socks4", "socks5")
  … (13 more lines — see the tool's home page)

• netdiscoverweb

  Active/passive ARP reconnaissance for finding live hosts on a local network.

  ayuda

  Netdiscover 0.21 [Active/passive ARP reconnaissance tool]
  Written by: Jaime Penalba <jpenalbae@gmail.com>
  
  Usage: netdiscover [-i device] [-r range | -l file | -p] [-m file] [-F filter] [-s time] [-c count] [-n node] [-dfPLNS]
    -i device: your network device
    -r range: scan a given range instead of auto scan. 192.168.6.0/24,/16,/8
    -l file: scan the list of ranges contained into the given file
    -p passive mode: do not send anything, only sniff
    -m file: scan a list of known MACs and host names
    -F filter: customize pcap filter expression (default: "arp")
    -s time: time to sleep between each ARP request (milliseconds)
    -c count: number of times to send each ARP request (for nets with packet loss)
    -n node: last source IP octet used for scanning (from 2 to 253)
    -d ignore home config files for autoscan and fast mode
    -R assume user is root or has the required capabilities without running any checks
    -f enable fastmode scan, saves a lot of time, recommended for auto
    -P print results in a format suitable for parsing by another program and stop after active scan
    -L similar to -P but continue listening after the active scan is completed
    -N Do not print header. Only valid when -P or -L is enabled.
    -S enable sleep time suppression between each request (hardcore mode)
  
  If -r, -l or -p are not enabled, netdiscover will scan for common LAN addresses.

• netmaskweb

  Helps derive and explain network masks and ranges when scoping or reading address plans.

  ayuda

  This is netmask, an address netmask generation utility
  Usage: netmask spec [spec ...]
    -h, --help			Print a summary of the options
    -v, --version			Print the version number
    -d, --debug			Print status/progress information
    -s, --standard		Output address/netmask pairs
    -c, --cidr			Output CIDR format address lists
    -i, --cisco			Output Cisco style address lists
    -r, --range			Output ip address ranges
    -x, --hex			Output address/netmask pairs in hex
    -o, --octal			Output address/netmask pairs in octal
    -b, --binary			Output address/netmask pairs in binary
    -n, --nodns			Disable DNS lookups for addresses
    -f, --files			Treat arguments as input files
  Definitions:
    a spec can be any of:
      address
      address:address
      address:+address
      address/mask
    an address can be any of:
      N		decimal number
      0N		octal number
      0xN		hex number
      N.N.N.N	dotted quad
      hostname	dns domain name
    a mask is the number of bits set to one from the left

• p0fweb

  Passive OS fingerprinting from observed traffic without sending probes of your own.

• recon-ngrecon-cliweb

  Modular web reconnaissance framework for chaining public-data collectors with a workspace you can export.

  ayuda

  usage: recon-cli [-h] [-w workspace] [-C command] [-c command] [-G]
                   [-g name=value] [-M] [-m module] [-O] [-o name=value] [-x]
                   [--no-version] [--no-analytics] [--no-marketplace]
                   [--stealth] [--version] [--analytics]
  
  recon-cli - Tim Tomes (@lanmaster53)
  
  options:
    -h, --help        show this help message and exit
    -w workspace      load/create a workspace
    -C command        runs a command at the global context
    -c command        runs a command at the module context (pre-run)
    -G                show available global options
    -g name=value     set a global option (can be used more than once)
    -M                show modules
    -m module         specify the module
    -O                show available module options
    -o name=value     set a module option (can be used more than once)
    -x                run the module
    --no-version      disable version check. Already disabled by default in
                      Debian
    --no-analytics    disable analytics reporting. Already disabled by default
                      in Debian
    --no-marketplace  disable remote module management
    --stealth         disable all passive requests (--no-*)
    --version         displays the current version
    --analytics       enable analytics reporting. Send analytics to google

• smtp-user-enumweb

  Guesses valid users on SMTP services that leak existence via VRFY, EXPN, or RCPT quirks.

  ayuda

  /usr/bin/smtp-user-enum version [unknown] calling Getopt::Std::getopts (version 1.14 [paranoid]),
  running under Perl version 5.42.2.
  
  Usage: smtp-user-enum [-OPTIONS [-MORE_OPTIONS]] [--] [PROGRAM_ARG1 ...]
  
  The following single-character options are accepted:
  	With arguments: -m -u -U -s -S -r -t -T -M -f -D -p -w
  	Boolean (without arguments): -d -v -h
  
  Options may be merged together.  -- stops processing of options.
  Space is not required between options and their arguments.
    [Now continuing due to backward compatibility and excessive paranoia.
     See 'perldoc Getopt::Std' about $Getopt::Std::STANDARD_HELP_VERSION.]
  smtp-user-enum v1.2 ( http://pentestmonkey.net/tools/smtp-user-enum )
  
  Usage: smtp-user-enum [options] ( -u username | -U file-of-usernames ) ( -t host | -T file-of-targets )
  
  options are:
          -m n     Maximum number of processes (default: 5)
  	-M mode  Method to use for username guessing EXPN, VRFY or RCPT (default: VRFY)
  	-u user  Check if user exists on remote system
  	-f addr  MAIL FROM email address.  Used only in "RCPT TO" mode (default: user@example.com)
          -D dom   Domain to append to supplied user list to make email addresses (Default: none)
                   Use this option when you want to guess valid email addresses instead of just usernames
                   e.g. "-D example.com" would guess foo@example.com, bar@example.com, etc.  Instead of
                        simply the usernames foo and bar.
  	-U file  File of usernames to check via smtp service
  	-t host  Server host running smtp service
  	-T file  File of hostnames running the smtp service
  	-p port  TCP port on which smtp service runs (default: 25)
  	-d       Debugging output
  	-w n     Wait a maximum of n seconds for reply (default: 5)
  	-v       Verbose
  	-h       This help message
  
  Also see smtp-user-enum-user-docs.pdf from the smtp-user-enum tar ball.
  
  Examples:
  
  $ smtp-user-enum -M VRFY -U users.txt -t 10.0.0.1
  $ smtp-user-enum -M EXPN -u admin1 -t 10.0.0.1
  $ smtp-user-enum -M RCPT -U users.txt -T mail-server-ips.txt
  $ smtp-user-enum -M EXPN -D example.com -U users.txt -t 10.0.0.1

• snmpchecksnmp-checkweb

  Enumerates an SNMP agent once you have a community string: interfaces, processes, and software claims.

  ayuda

  snmp-check v1.9 - SNMP enumerator
  Copyright (c) 2005-2015 by Matteo Cantoni (www.nothink.org)
  
   Usage: snmp-check [OPTIONS] <target IP address>
  
    -p --port        : SNMP port. Default port is 161;
    -c --community   : SNMP community. Default is public;
    -v --version     : SNMP version (1,2c). Default is 1;
  
    -w --write       : detect write access (separate action by enumeration);
  
    -d --disable_tcp : disable TCP connections enumeration!
    -t --timeout     : timeout in seconds. Default is 5;
    -r --retries     : request retries. Default is 1;
    -i --info        : show script version;
    -h --help        : show help menu;

• socatweb

  Multipurpose relay for sockets, files, and pipes; handy for simple listeners and port forwards.

  ayuda

  socat - Multipurpose relay
  
  Usage:
    socat [options] <address> <address>

• swaksweb

  SMTP Swiss army knife for crafting test mail transactions when email paths are in scope.

  ayuda

  SWAKS(1)                             SWAKS                             SWAKS(1)
  
  NAME
       Swaks - Swiss Army Knife SMTP, the all-purpose SMTP transaction tester
  
  DESCRIPTION
       Swaks'  primary  design goal is to be a flexible, scriptable, transaction-
       oriented SMTP test tool.  It handles SMTP features and extensions such  as
       TLS, authentication, and pipelining; multiple version of the SMTP protocol
       including  SMTP, ESMTP, and LMTP; and multiple transport methods including
       UNIX-domain  sockets,  internet-domain  sockets,  and  pipes  to   spawned
       processes.   Options can be specified in environment variables, configura‐
       tion files, and the command line allowing maximum configurability and ease
       of use for operators and scripters.
  
  QUICK START
       Deliver  a  standard  test  email  to  user@example.com  on  port  25   of
       test-server.example.net:
  
        swaks --to user@example.com --server test-server.example.net
  
       Deliver  a  standard test email, requiring CRAM-MD5 authentication as user
       me@example.com.  An "X-Test" header will be added to the email body.   The
       authentication password will be prompted for if it cannot be obtained from
       your .netrc file.
  
        swaks --to user@example.com --from me@example.com --auth CRAM-MD5 --auth-user me@example.com --header-X-Test "test email"
  
       Test a virus scanner using EICAR in an attachment.  Don't show the message
       DATA part.:
  
        swaks -t user@example.com --attach - --server test-server.example.com --suppress-data </path/to/eicar.txt
  
       Test a spam scanner using GTUBE in the body of an email, routed via the MX
       records for example.com:
  
        swaks --to user@example.com --body @/path/to/gtube/file
  
       Deliver  a standard test email to user@example.com using the LMTP protocol
       via a UNIX domain socket file
  
        swaks --to user@example.com --socket /var/lda.sock --protocol LMTP
  
       Report all the recipients in a text file that are non-verifiable on a test
       server:
  … (115 more lines — see the tool's home page)

• thc-ipv6atk6-address6web

  IPv6 attack and discovery toolkit from THC for labs that actually route v6.

  ayuda

  Error: neither a valid mac, IPv4 or IPv6 address

• theharvesterrestfulHarvestweb

  Collects emails, names, and subdomains from public sources so OSINT starts from what the internet already admits.

  ayuda

  usage: restfulHarvest [-h] [-H HOST] [-p PORT] [-l LOG_LEVEL] [-r]
                        [--rate-limit RATE_LIMIT]
  
  options:
    -h, --help            show this help message and exit
    -H, --host HOST       IP address to listen on default is 127.0.0.1
    -p, --port PORT       Port to bind the web server to, default is 5000
    -l, --log-level LOG_LEVEL
                          Set logging level, default is info but
                          [critical|error|warning|info|debug|trace] can be set
    -r, --reload          Enable automatic reload used during development of the
                          api
    --rate-limit RATE_LIMIT
                          Set API rate limit (e.g., "10/minute", "100/hour"),
                          default is 5/minute

• unicornscanfantaipweb

  Userland asynchronous scanner for flexible TCP/UDP probing when you need alternate timing models.

  ayuda

  FantaIP by Kiki
  Usage: fantaip (options) IP
  	-d		Detach from terminal and daemonize
  	-H		Hardware address like XX:XX:XX:XX:XX:XX (otherwise use nics hwaddr)
  	-h		help
  	-i		*interface
  	-v		verbose operation
  *: Argument required
  Example: fantaip -i eth0 192.168.1.7

• urlcrazyweb

  Generates domain typos and lookalikes to hunt phishing or brand-abuse registrations.

• zenmapweb

  Graphical front end for nmap when you want topology views and saved scan profiles instead of only CLI output.

Cuando hay un propósito escrito para esta ruta, se muestra primero. Si no, ves el resumen del paquete. La ayuda se captura en vivo desde un Kali cuando está disponible.